Hi there, really enjoying orac !!!
Wanted to expand more, but I have verry little knowledge of linux 
yes you can add new modules, they get placed in
~/media/orac/usermodules/
generally, modules are compatible
however, some are developing modules which have graphics components which is outside of the Orac API.
I’ve always suggested that this are done in addition to parameters which would work without graphics, but this is not always done - so mileage will vary depending on modules.
Many thanks mark !
Hi @thetechnobear. I am also using orac 2 through a pisound as a guitar effects rack. I am having a problem with adding effects after I raise the gain on a chain. If I set up a parallel in, say, a1, and raise the gain, I only get a signal (stereo at that), when I raise the left gain. The right gain doesn’t really do anything. Also, and I suspect these are related problems, once I add an effect to, say, a2 (like a simple delay), I get no signal at all. I have a feeling I’m missing something very basic here, but haven’t found a similar problem referenced in the boards. Thanks in advance for any help.
If you’re not passing in a stereo signal, then you should pan it to centre in the router.
Note: a lot of the fx do not accept stereo inputs, they either sum L+R or just use left channel.
Thanks so much, Mark. I’ve tried various adjustments to pan and gain, and I’ve experimented with stereo and mono inputs and outputs. I think I have the hang of that part of things.
I’m still having an issue with setting up chains with effects. I begin the chain with a parallel router, set up the gain and get a signal, then I add an effect to the second part of the chain and there’s no signal. I’ve run through all the effects in orac with the same result.
I reinstalled the patchbox os on my raspberry Pi 3B+ with a pisound. I also updated everything on the pi from the command line. I’m plugging the guitar into the pisound and sending the out to a Zoom H5 recorder.
The router is install by default in s1 , you do not need another one, and adding another will cause issues.
Thanks very much, Mark. I will try that. Happy New Year!
Where do I find info on how to make my own patches/chains? Great instructions on installation and setup and great overview of the structure, layout, and signal flow but nowhere have I found how or where to install modules or worse, how to actually load modules into chains. I installed the web client but there’s nothing to make a new "patch where I can load modules how I see fit.
So, what’s the missing link here? How do you actually load modules into chains and set/maniuplate parameters? I feel like that was just skipped/implied in all the docs I’ve read over the last few hours.
Any help or links to docs with this information would be great!
Hi, my midi boy as just arrived, and i was trying the orac control sketch; i plugged it into my pi, and there is alway the same message waiting for orac bridge? does anyone as tryed before or is there somethng to do in orac to make it working? thank you
so easy! lets make some noise!
@thetechnobear Hello! I am working on getting Orac running on a Pi 4 without pisound. I am having difficulty with usermodules running. I followed the steps in post from May 2019 but when I run
journalctl -u orac
I end up with:
– Logs begin at Wed 2020-05-20 19:27:56 BST, end at Wed 2020-05-20 20:44:27 BST
May 20 19:28:18 patchbox systemd[1]: Started Run Orac at boot.
May 20 19:28:19 patchbox pd[629]: opened alsa client 130 in:1 out:1
May 20 19:28:19 patchbox pd[629]: error: JACK: cannot connect input ports system
May 20 19:28:19 patchbox pd[629]: error: JACK: cannot connect input ports system
May 20 19:28:19 patchbox pd[629]: unable to parse preferences file : orac.json
May 20 19:28:19 patchbox pd[629]: error around : “userModuleDir”: " /home/patch/
May 20 19:28:19 patchbox pd[629]: }
May 20 19:28:19 patchbox pd[629]: KontrolRack: device = midi
May 20 19:28:19 patchbox pd[629]: client connected pd.osc:127.0.0.1:6000
May 20 19:28:19 patchbox pd[629]: KontrolRack::loading resources
May 20 19:28:19 patchbox pd[629]: KontrolRack::module found: fx/bitcrusher
May 20 19:28:19 patchbox pd[629]: KontrolRack::module found: fx/chorus
May 20 19:28:19 patchbox pd[629]: KontrolRack::module found: fx/clds
Any thoughts on why this may be?
Is jack service running? (sudo systemctl status jack) If not, reconfigure it by running patchbox, going to jack menu.
Yes, it is active and running! I get the following output
patch@patchbox:~ $ sudo systemctl status jack
● jack.service - JACK Server
Loaded: loaded (/lib/systemd/system/jack.service; enabled; vendor preset: enabled)
Active: active (running) since Wed 2020-05-20 22:07:47 BST; 20min ago
Main PID: 485 (jackd)
Tasks: 5 (limit: 4915)
Memory: 87.8M
CGroup: /system.slice/jack.service
└─485 /usr/bin/jackd -t 2000 -R -P 95 -d alsa -d hw:ALSA -r 44100 -p 512 -n 3 -X seq -s -SMay 20 22:08:00 patchbox jackdrc[485]: JackGraphManager::Connect different port types port_src = 6 port_dst = 8
May 20 22:08:00 patchbox jackdrc[485]: port created: MEC-MIDI-OUTPUT:midi/playback_1
May 20 22:08:02 patchbox jackdrc[485]: port created: RtMidiIn-Client:midi/capture_1
May 20 22:08:02 patchbox jackdrc[485]: port created: RtMidiOut-Client:midi/playback_1
May 20 22:12:34 patchbox jackdrc[485]: JackGraphManager::Connect different port types port_src = 3 port_dst = 7
May 20 22:12:50 patchbox jackdrc[485]: port created: Pure-Data:midi/capture_1
May 20 22:12:50 patchbox jackdrc[485]: port created: Pure-Data:midi/playback_2
May 20 22:12:50 patchbox jackdrc[485]: JackEngine::XRun: client = PulseAudio JACK Sink was not finished, state = Running
May 20 22:12:50 patchbox jackdrc[485]: JackGraphManager::Connect different port types port_src = 3 port_dst = 20
May 20 22:12:50 patchbox jackdrc[485]: JackGraphManager::Connect different port types port_src = 6 port_dst = 21
Have you edited the ‘orac.json’ file? Could you paste the contents you have here?
Not relevant anymore, moved to Getting no sound output from Raspberry's built in analog output
Just (mostly) successfully got Orac working on my Raspberry Pi 3b+. I’m using patchbox, and managed to tweak settings to get a behringer UCA202 working (haven’t checked for latency yet…). Ableton Link sometimes works, sometimes doesn’t (but that’s another story)…
My problem is that access to S1 via main.pd has disappeared completely. It doesn’t show up in demo 1. demo 2 or the init patch. I’ve arrowed left and right like crazy thinking I’ve missed it, closed and restarted pd, even rebooted the pi. It’s obviously still working because the demo patch is still chuntering away on both active chains and the midiout I added & saved to the demo is still going, but I can’t edit S1 at all because it doesn’t show up. Do I need to reinstall?
Never mind, S1 is back. I restarted the Pi again and launched main.pd. Demo1 appears complete again with all the modules available.
Decidely odd though. I don’t see this happening to anyone else. Orac is fantastic work and I look forward to working with it.
